JK2060AC
兩相混合式步進電機驅動器
2phase hybrid stepper motor driver
概述
JK2060AC 兩相混合式步進電機驅動器，采用交流24V~50V,直流30V~80V輸入,，適合驅動電流小于6.0A,外徑在86mm的混合式步進電機使用。此驅動器采用交流伺服驅動器的電流環進行細分控制，電機低速運行平穩，高速力矩穩定。廣泛適合于各類CNC機械，機器人，切割機，包裝機，繪圖儀，雕刻機等，
Descriptions
JK2060AC is a type of 2 phase hybrid steppermotor driver , this driver input voltage is 24~50V AC ,30V~80V DC, suit for currentless 6.0A, diameter is 86mm 2 phase hybrid stepper motor .this driver thatadopts similar to the Circuit of servo control which enables the motor to run smoothly. It is widely used in CNC machine , robots,cuttingmachine,packing machine,plotter, engraving machine and so on.
特點
*平均電流控制，兩相正弦電流輸出
*交流24~60V，直流30V~80V
*光電隔離信號輸入、輸出
*有過壓-﹑欠壓-﹑過流-﹑相間短路保護功能
*十四檔細分和自動半流功能
*八檔輸出相電流設置
*可驅動任何6.0A相電流以下兩相、四相混合式步進電機,
*主要適合驅動86mm(NEMA34)兩相步進電機
Features
*Averagecurrent control,2 phase sinusoidal output current drive
*supplyvoltage from 24VAC~50VAC,30VDC~80VDC
*Opto-isolatedsignal I/O
*Overvoltage,under voltage,overcurrent,phase short cicuit protection
*14channels subdivision and automatic idle-current reduction
*8channels output phase current setting
*Can drive 2 phase and 4phase hybrid stepper motor when phase current less than 6.0A
*mainlyfor 86mm(NEMA34)2 phase stepper motor
性能指標
輸入電壓 交流20V~60V, 直流30V~80V
輸出電流 2.0A~6.0A
溫 度 工作溫度-10°~45°，存放溫度-20°~125°
環境濕度 不凝露，不結霜
氣 體 禁止有可燃?xì)怏w和導電灰塵
重 量 600克
MechanicalSpecification
Input Voltage 20~60V AC, 30~80V DC
Output current 2.0A~6.0A
Temperature working temperature -10°~45°,stockingtemperature ~20°~70°
Humidity Not condensation , no water droplets
Gas Prohibition of combustible gasesａnd conductive dust
Weight 600g
MechanicalDimension （mm）
